This document explains the requirements for end-point assessment (EPA) for the bricklayer apprenticeship. End-point assessment organisations (EPAOs) must follow this when designing and delivering the EPA.

Bricklayer apprentices, their employers and training providers should read this document.

A full-time bricklayer apprentice typically spends 24 months on-programme (this means in training before the gateway). The apprentice must spend at least 12 months on-programme and complete the required amount of off-the-job training in line with the apprenticeship funding rules.

The apprentice must complete their training and meet the gateway requirements before starting their EPA. The EPA will assess occupational competence.

An approved EPAO must conduct the EPA for this apprenticeship. Employers must select an approved EPAO from the register of end-point assessment organisations (RoEPAO).

This EPA has 3 assessment methods.

The grades available for each assessment method are below.

Assessment method 1 - multiple-choice test:

• fail

• pass

• distinction

Assessment method 2 - interview underpinned by a portfolio of evidence:

• fail

• pass

• distinction

Assessment method 3 - practical assessment with questions:

• fail

• pass

• distinction

The result from each assessment method is combined to decide the overall apprenticeship grade. The following grades are available for the apprenticeship:

• fail

• pass

• merit

• distinction

The EPA is taken in the EPA period. The EPA period starts when the EPAO confirms the gateway requirements have been met and is typically 3 months.

The EPAO should confirm the gateway requirements have been met and the EPA should start as quickly as possible.

The apprentice’s employer must be content that the apprentice has attained sufficient KSBs to complete the apprenticeship. The employer may take advice from the apprentice's training provider, but the employer must make the decision. The apprentice will then enter the gateway.

The apprentice must meet the gateway requirements before starting their EPA.

They must:

• confirm they are ready to take the EPA
• have achieved English and maths qualifications in line with the apprenticeship funding rules

• submit a portfolio of evidence for the interview underpinned by a portfolio of evidence

Portfolio of evidence requirements:

The apprentice must compile a portfolio of evidence during the on-programme period of the apprenticeship. It should only contain evidence related to the KSBs that will be assessed by this assessment method. It will typically contain 10 discrete pieces of evidence. Evidence must be mapped against the KSBs. Evidence may be used to demonstrate more than one KSB; a qualitative as opposed to quantitative approach is suggested.

Evidence sources may include:

• workplace documentation and records, for example:
• workplace policies and procedures
• witness statements
• annotated photographs
• video clips (maximum total duration 10 minutes); the apprentice must be in view and identifiable

This is not a definitive list; other evidence sources can be included.

The portfolio of evidence should not include reflective accounts or any methods of self-assessment. Any employer contributions should focus on direct observation of performance (for example, witness statements) rather than opinions. The evidence provided should be valid and attributable to the apprentice; the portfolio of evidence should contain a statement from the employer and apprentice confirming this.

The EPAO should not assess the portfolio of evidence directly as it underpins the interview. The independent assessor should review the portfolio of evidence to prepare questions for the interview. They are not required to provide feedback after this review.

The apprentice must submit the gateway evidence to their EPAO, including any organisation specific policies and procedures requested by the EPAO.

The assessment methods can be delivered in any order.

The result of one assessment method does not need to be known before starting the next.

Overview

In the test, the apprentice answers questions in a controlled and invigilated environment. It gives the apprentice the opportunity to demonstrate the knowledge mapped to this assessment method.

Rationale

This assessment method is being used because:

• it allows for the efficient testing of knowledge where there is a right or wrong answer

• it allows for flexibility in terms of when, where and how it is taken.

Delivery

The test must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.

The multiple-choice test can be computer based.

The multiple-choice test must consist of 40 multiple-choice questions.

Multiple-choice questions must have four options, including one correct answer.

The apprentice must be given at least 14 days notice of the date and time of the multiple-choice test.

Test administration

The apprentice must have 60 minutes to complete the test.

The multiple-choice test is closed book which means that the apprentice cannot refer to reference books or materials whilst taking the test.

The multiple-choice test must be taken in the presence of an invigilator under the responsibility of the EPAO.

The EPAO must have an invigilation policy setting out how the multiple-choice test must be conducted. It must state the ratio of apprentices to invigilators for the setting and allow the test to take place in a secure way.

The EPAO is responsible for the security of the multiple-choice test including the arrangements for on-line testing. The EPAO must ensure that their security arrangements maintain the validity and reliability of the multiple-choice test.

Marking

The multiple-choice test must be marked by an independent assessor or marker employed by the EPAO. They must follow a marking scheme produced by the EPAO. Marking by computer is allowed where question type supports this.

A correct answer gets 1 mark.

Any incorrect or missing answers get zero marks.

The EPAO is responsible for overseeing the marking of the multiple-choice test. The EPAO must ensure standardisation and moderation of multiple-choice test.

Assessment location

The apprentice must take the multiple-choice test in a suitably controlled and invigilated environment that is a quiet room, free from distractions and influence. The EPAO must check the venue is suitable.

The multiple-choice test may take place remotely if the appropriate technology and systems are in place to prevent malpractice. The EPAO must ensure invigilation of the apprentice for example with, and not limited to, 360-degree cameras and screen sharing facilities.

Question and resource development

The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO should maintain the security and confidentiality of EPA materials when consulting employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.  

The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.

The EPAO must ensure that apprentice has a different set of questions in the case of re-sits or re-takes.

The EPAO must produce the following materials to support the multiple-choice test:

• independent assessor assessment materials which include:
  • training materials
  • administration materials
  • moderation and standardisation materials
  • guidance materials
  • grading guidance
  • test specification
  • sample test and mark schemes
  • live tests and mark schemes
  • question bank
• EPA guidance for the apprentice and the employer

The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation, training, and moderation.

Overview

In the interview, an independent assessor asks the apprentice questions. The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence. It gives the apprentice the opportunity to demonstrate the KSBs mapped to this EPA method.

Rationale

This assessment method is being used because:

• it allows the apprentice to be assessed against KSBs which may not naturally occur during the practical assessment

• it is underpinned by a portfolio of evidence, enabling the apprentice to demonstrate the application of skills and behaviours as well as knowledge

• it allows for testing of responses where there are a number of potential answers that could not be tested through a multiple-choice test

• it is cost-effective.

Delivery

The interview must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.

An independent assessor must conduct and assess the interview.

The purpose of the independent assessor's questions will be to allow the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method at the highest possible grade.

The EPAO must give an apprentice 14 days notice of the interview.

The independent assessor must have at least 2 week(s) to review the supporting documentation.

The apprentice must have access to their portfolio of evidence during the interview.

The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence is however the portfolio of evidence is not directly assessed.

The interview must last for 60 minutes. The independent assessor can increase the time of the interview by up to 10%. This time is to allow the apprentice to respond to a question if necessary.

The independent assessor must ask at least 10 questions. Follow-up questions are allowed where clarification is required. The independent assessor must use the questions from their EPAO’s question bank or create their own questions in-line with the EPAO’s training.

The independent assessor must make the grading decision. The independent assessor must keep accurate records of the assessment. They must record:

• the apprentice’s answers to questions
• the KSBs demonstrated in answers to questions
• the grade achieved 

Assessment location

The interview must take place in a suitable venue selected by the EPAO (for example the EPAO’s or employer’s premises).

The interview should take place in a quiet room, free from distractions and influence.

Question and resource development

The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO should maintain the security and confidentiality of EPA materials when consulting employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.  

The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.

The EPAO must ensure that apprentice has a different set of questions in the case of re-sits or re-takes.

The EPAO must produce the following materials to support the interview underpinned by a portfolio of evidence:

• independent assessor assessment materials which include:

• training materials
• administration materials
• moderation and standardisation materials
• guidance materials
• grading guidance
• question bank

• EPA guidance for the apprentice and the employer

The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation, training, and moderation.

Overview

In a practical assessment with questions, an independent assessor observes the apprentice completing a task or series of tasks set by the EPAO. The EPAO decides where it takes place. The assessment environment must closely relate to the apprentice’s natural working environment. This allows the apprentice to demonstrate the KSBs mapped to this assessment method. 

Rationale

This assessment method is being used because:

• it allows for a varied range of tasks to be observed, that could not be guaranteed to be achieved through a single observation in the workplace
• this is a practical role, best demonstrated through completing tasks in a realistic work setting
• it allows for consistency of activities to be completed and efficiency in scheduling
• it allows for the testing of related underpinning knowledge, skills and behaviours where an opportunity to observe them has not occurred
• it is a holistic assessment method

Delivery

The practical assessment with questions must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.

An independent assessor must conduct and assess the practical assessment with questions.

The independent assessor must only observe a maximum of four apprentices at any one time to ensure quality and rigour. They must be as unobtrusive as possible. The EPAO must ensure that an apprentice cannot gain advantage from seeing what the other apprentices being assessed are doing or by hearing answers to questions.

The EPAO must give an apprentice 14 days notice of the . practical assessment with questions

The practical assessment with questions must take 12 hours.

The independent assessor can increase the time of the practical assessment with questions by up to 10%. This time is to allow the apprentice to complete a task or respond to a question if necessary.

The practical assessment with questions may take place in parts but must be completed over 2 working day(s). A working day is typically considered to be 7.5 hours long. The reason for this split is to provide sufficient time for the apprentice to complete all elements of the practical task.

EPAOs must manage invigilation of the apprentice during the assessment, to maintain security of the EPA, in line with their malpractice policy. This includes breaks and moving between locations during the working day.

The independent assessor must explain to the apprentice the format and timescales of the practical assessment with questions before it starts. This does not count towards the assessment time.

The independent assessor must observe the following during the practical assessment:

Construction of a section of stretcher bond brick and standard block cavity wall (minimum brick face size of 1565mm length and 900mm height) with corner return (minimum brick face size of 665mm length and 900mm height), incorporating:

• a minimum opening size of 450mm length and 450mm height with pre-formed cavity closures

• partial fill insulation and wall tie retaining clips

• fire stopping

• damp proof course (DPC)

• wall ties

• weep holes

• a lintel with brick soldier course

• cavity tray

• brick on edge sill with projection

• two applied finishes to the brick mortar joints, one of which must be half-round.

The stretcher bond brick and standard block cavity wall must be compliant with building regulations.

To minimise predictability in future versions of the assessment, a range of different scenarios will be incorporated into the cavity wall assessment. For example, differential window positions, brick face lengths, sill projections, brick jointing finishes and the use of contrasting bricks for brick sills and soldier courses etc.

It is anticipated that a competent bricklayer at this level will be able to handle 25 bricks per hour or 12 standard blocks per hour when carrying out standard cavity wall work or 15 bricks per hour when carrying out brick sills and soldier courses.

Typically, 60 minutes should be allocated within the EPA total time to interpret and extract relevant information from drawings, specifications and work instructions. This time will also enable estimation of resources and initial setting out.

Typically, 60 minutes should be allocated within the EPA total time to allow for the installation of fire stopping, lintel, cavity tray, weep holes, DPC, insulation and pre-formed cavity closures.

KSBs observed, and answers to questions must be documented by the independent assessor. The independent assessor will make all grading decisions in line with specification tolerances and grading descriptors. An additional competent person may be present to mix mortar and move materials as required.

Specification tolerances:

• length of brick and standard block walling +or- 3mm per metre

• brick and standard block return square (90 degree) +or- 3mm

• opening size and position +or- 3mm

• brick and standard block plumbing points +or- 3 mm per metre

• block and standard block level +or- 3mm per metre

• brick and standard block gauge +or- 3mm per metre

• opening brick and standard block plumb +or- 3mm per metre

• plumb, gauge and level of soldier course +or- 3mm

• slope of Brick on-edge sill +or- 3 degree from a 15 degree slope

• sill projection +or- 3mm

• horizontal level of brick on edge sill +or- 3 mm

• brick and standard blocks cutting accuracy +or- 3mm

The following must be installed in line with building regulation requirements:

• partial fill insulation and wall tie retaining clips

• fire stopping

• DPC

• wall ties

• weep holes

• lintel

• cavity tray

These activities provide the apprentice with the opportunity to demonstrate the KSBs mapped to this assessment method.

The independent assessor must ask questions. The purpose of the questions is to explore aspects of the KSBs not demonstrated in the practical assessment and show depth of understanding.

Questioning can occur during practical assessment. The time for questions asked during the practical assessment is included in the overall assessment time.

Independent assessors must ask at least 6 questions during the practical assessment. To remain as unobtrusive as possible, the independent assessor should ask questions during natural breaks in work rather than disrupting the apprentice’s flow. The independent assessor must use the questions from their EPAO’s question bank or create their own questions in-line with the EPAO’s training.

The independent assessor can ask follow-up questions to clarify answers given by the apprentice. These questions are in addition to the above set number of questions for the practical assessment with questions and should be kept to a minimum.

The independent assessor must keep accurate records of the assessment. They must record:

• the KSBs observed
• The apprentice’s answers to questions
• KSBs demonstrated in answers to questions
• the grade achieved

The independent assessor must make the grading decision. The practical assessment and responses to questions must be assessed holistically by the independent assessor when they are deciding the grade. 

Assessment location

The practical assessment with questions will take place in a simulated environment selected by the EPAO (for example the EPAO’s or employer’s premises). The simulated environment must relate to the apprentice’s natural work environment. Equipment and resources needed for the practical assessment with questions must be provided by the EPAO, who can liaise with the employer to provide these.

Question and resource development

The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO should maintain the security and confidentiality of EPA materials when consulting employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.  

The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.

The EPAO must ensure that the apprentice has a different set of questions in the case of re-sits or re-takes.

The EPAO must produce the following materials to support the practical assessment with questions:

• independent assessor assessment materials which include:
  • training materials
  • administration materials
  • moderation and standardisation materials
  • guidance materials
  • grading guidance
  • question bank
• EPA guidance for the apprentice and the employer

Performance in the EPA determines the overall grade of:

• fail

• pass

• merit

• distinction

An independent assessor must individually grade the: interview underpinned by a portfolio of evidence and practical assessment with questions in line with this EPA plan.

The EPAO must combine the individual assessment method grades to determine the overall EPA grade.

If the apprentice fails one assessment method or more, they will be awarded an overall fail.

To achieve an overall pass, the apprentice must achieve at least a pass in all the assessment methods. To achieve an overall EPA merit, the apprentice must gain a distinction in at least two of the assessment methods and a pass in the other. To achieve an overall EPA distinction, the apprentice must gain a distinction in all the assessment methods.

Grades from individual assessment methods must be combined in the following way to determine the grade of the EPA overall.

If the apprentice fails one or more assessment methods they can take a re-sit or a re-take at their employer’s discretion. The apprentice’s employer needs to agree that a re-sit or re-take is appropriate. A re-sit does not need further learning, whereas a re-take does.

The apprentice should have a supportive action plan to prepare for a re-sit or a re-take.

The employer and EPAO agree the timescale for a re-sit or re-take. A re-sit is typically taken within 3 months of the EPA outcome notification. The timescale for a re-take is dependent on how much re-training is required and is typically taken within 6 months of the EPA outcome notification.

Failed assessment methods must be re-sat or re-taken within a 6-month period from the EPA outcome notification, otherwise the entire EPA will need to be re-sat or re-taken in full.

Re-sits and re-takes are not offered to an apprentice wishing to move from pass to a higher grade.

The apprentice will get a maximum EPA grade of pass for a re-sit or re-take, unless the EPAO determines there are exceptional circumstances.

The EPAO must have reasonable adjustments arrangements for the EPA.

This should include:

• how an apprentice qualifies for reasonable adjustment
• what reasonable adjustments may be made

Adjustments must maintain the validity, reliability and integrity of the EPA as outlined in this EPA plan.

Internal quality assurance refers to how the EPAO ensures valid, consistent and reliable EPA decisions. The EPAO must adhere to the requirements within the roles and responsibilities section:

The EPAO must also:

• have quality assurance systems and procedures that ensure fair, reliable and consistent EPA regardless of employer, place, time or independent assessor
• appoint independent assessors who are competent to deliver the EPA and who:
  • have recent relevant experience of the occupation or sector to at least occupational level 3 gained in the last 3 years or significant experience of the occupation or sector
• operate induction training for anyone involved in the delivery or assessment of the EPA
• provide training for independent assessors in good assessment practice, operating the assessment tools and making grading decisions
• provide ongoing training for markers and invigilators
• provide standardisation activity for this apprenticeship standard for all independent assessors:
  • before they conduct an EPA for the first time
  • if the EPA is updated
  • periodically as appropriate (a minimum of annually)
• conduct effective moderation of EPA decisions and grades
• conduct appeals where required, according to the EPAO’s appeals procedure, reviewing and making final decisions on EPA decisions and grades
• have no direct connection with the apprentice, their employer or training provider.

Affordability of the EPA will be aided by using at least some of the following:

• completing applicable assessment methods online (for example computer-based assessment)

• utilising digital remote platforms to conduct applicable assessment methods

• assessing multiple apprentices simultaneously where the method of assessment permits this

• using the employer’s premises

• conducting assessment methods on the same day

Professional body recognition is not relevant to this occupational apprenticeship.